Use the instant filter bar below to narrow product families by form, supplied finish state, candidate thickness, or target building application, and compare up to three specifications side by side.
Mass-pigmented core · Requires zero site painting · 4 Textures · 7 Product Colours + 5 Topcoats · Class A1
Autoclaved 1250 × 2500 × 10 mm (3.125 m² · 60 pcs/pallet) panels pigmented throughout their full cross-section in Smooth, Striped, Stone and Wood textures.
Natural grey unprimed or factory pre-primed · 6 Sub-Groups (33 Models) · 6–20 mm · Class A1
Complete autoclaved fibre cement range: Smooth (Int./Ext.), 12 Embossed & Calibrated Boards, 10 Grooved Profiles (Type 01–05 & A–E), 2 Cornice Profiles, 6 Window Jambs and Lap Siding.
8 + 8 mm Class A1 Faces · 16 DNS EPS Core (XPS/Rockwool/PUR on MOQ) · 60 / 80 / 100 mm
Composite ready-wall press-panels bonding two 8 mm autoclaved fibre cement boards to an EPS insulation core across 1250 × 2500 / 3000 mm in Smooth and 5 Architectural Wood/Stone reliefs.
Pigmented throughout the mineral core during manufacturing so cut edges match the surface—requiring zero site painting across 7 base colours and 5 optional topcoats (1250 × 2500 × 10 mm).
Autoclaved 1250 × 2500 × 10 mm mass-pigmented flat facade board (EN 12467+A2 Cat. A, Class A1, RL ≥ 0.75) requiring zero site painting across 7 core shades and 5 solution topcoats.
Common Enquiry Formats: 1250 × 2500 mm
Rhythmic linear-striped architectural relief pressed into a mass-pigmented 1250 × 2500 × 10 mm Class A1 facade & interior panel requiring zero site painting.
Common Enquiry Formats: 1250 × 2500 mm
Natural stone surface relief pressed into a 1250 × 2500 × 10 mm mass-pigmented Class A1 sheet—far lighter, faster to cut and easier to install than quarried stone with zero site painting.
Common Enquiry Formats: 1250 × 2500 mm
Warm natural timber-grain relief pressed into a mass-pigmented 1250 × 2500 × 10 mm Class A1 mineral core—delivering rot-proof, pest-proof interior and exterior cladding with zero painting.
Common Enquiry Formats: 1250 × 2500 mm
Architectural coloured panels clearly differentiated between Factory-Coated opaque/semi-transparent finishes and Through-Coloured pigmented mineral cores.
Common Enquiry Formats: 1250 × 2500 · 1250 × 3000 mm
Autoclaved smooth interior (Category C) and exterior (Category A) flat boards supplied natural grey unprimed or factory pre-primed across 1250 × 2500 / 2800 / 3000 mm.
High-strength autoclaved EN 12467 Category C (Class 3, MOR ≥ 10.0 N/mm²) A1 non-combustible interior board across 22 format-thickness variants including 1250 × 2800 mm floor-to-ceiling partitions.
Common Enquiry Formats: 1250 × 2500 · 1250 × 2800 · 1250 × 3000 mm
Weather-engineered EN 12467 Category A autoclaved exterior facade board with low thermal expansion (αt = 0.005 mm/mK), freeze-thaw durability and Class A1 fire safety across 16 variants.
Common Enquiry Formats: 1250 × 2500 · 1250 × 3000 mm
Flat, calm architectural mineral boards supplied raw, factory-primed or coated for ventilated facades, light-steel assemblies and interior linings.
Common Enquiry Formats: 1250 × 2500 · 1250 × 2800 · 1250 × 3000 mm
All 12 distinct surface textures: Walnut/Cedar Wood, Slate Stone, Natural Stone, Decorative Stone, Staggered Brick, Woven Stone, Mixed Stone, Small & Large Block Stone, Striped, Sanded and Double-Sided Calibrated boards.
Complete 12-model family of autoclaved Class A1 paintable relief & precision-sanded boards (8 / 10 / 12 mm) delivering timber, stone and brick aesthetics without rot or fire risk.
Common Enquiry Formats: 1250 × 2500 · 1225 × 2590 · 615 × 2460 mm
Full-format mineral boards embossed with directional walnut or cedar timber grain for ventilated facades, modular housing and commercial elevations.
Common Enquiry Formats: 1250 × 2500 · 1250 × 3000 mm
Lightweight Class A1 cleft-slate stone relief board in 1250 × 2500 × 10 / 12 mm—easily sawn to custom ashlar modules and finished in any exterior acrylic colour.
Common Enquiry Formats: 1250 × 2500 mm
Deeply moulded slate, split-stone and layered rock relief boards in 10–12 mm thicknesses for plinths, prefab villas and ventilated commercial elevations.
Common Enquiry Formats: 1250 × 2500 · 1250 × 3000 mm
Impact-resistant 10 & 12 mm decorative stone relief sheets in 1250 × 2500 / 3000 mm that cut cleanly to custom stone formats and accept any water-based facade paint.
Common Enquiry Formats: 1250 × 2500 · 1250 × 3000 mm
Moulded running-bond brick relief panels in pattern-matched 1225 × 2590 mm and 1225 × 3000 mm formats (10–12 mm) for modular housing and ventilated facades.
Common Enquiry Formats: 1225 × 2590 · 1225 × 3000 mm
Coursed hand-laid stone wall relief in masonry-calibrated 1250 × 2620 mm (3.275 m²) and 1250 × 3000 mm (3.750 m²) sheets (10 & 12 mm), impervious to severe weather and chemicals.
Common Enquiry Formats: 1250 × 2620 · 1250 × 3000 mm
Multi-dimensional ashlar stone wall relief on 1225 × 2500 / 3000 mm (10 & 12 mm) sheets, cutting material and masonry labour time dramatically.
Common Enquiry Formats: 1225 × 2500 · 1225 × 3000 mm
Precision-machined 12 mm autoclaved panel featuring a 6×12 grid of 92.5 × 195 mm small stone blocks on a 615 × 2460 mm (1.513 m²) module (100 pcs/pallet).
Common Enquiry Formats: 92,5×195 - 615 × 2460 mm
Monumental 3×6 ashlar block grid (195 × 400 mm blocks) precision-machined from 12 mm autoclaved smooth boards in 615 × 2460 × 12 mm format (1.513 m² · 100 pcs/pallet).
Common Enquiry Formats: 195×400 - 615 × 2460 mm
Ultra-modern fine linear-striped 1250 × 2500 × 10 mm (60 pcs/pallet) paintable Class A1 board creating crisp directional micro-shadows across minimalist interiors and facades.
Common Enquiry Formats: 1250 × 2500 mm
Single-side front-sanded autoclaved board (8 / 10 / 12 mm in 1250 × 2500 & 3000 mm) ensuring gauged thickness uniformity and superior coating/adhesive key.
Common Enquiry Formats: 1250 × 2500 · 1250 × 3000 mm
Both front and back faces precision-calibrated by industrial sanding (8 / 10 / 12 mm in 1250 × 2500 & 3000 mm) for HPL/foil lamination, sandwich panels and structural bonding.
Common Enquiry Formats: 1250 × 2500 · 1250 × 3000 mm
12 mm autoclaved interlocking & channel-grooved facade boards across New-Generation Type 01–05 (2500 mm) and Classic Type A–E (2500 / 3000 mm), produced in Smooth, Cedar, Walnut, Natural Stone, Decorative Stone and Slate patterns.
Directional ribbed and grooved architectural panels (10–12 mm, 1250 × 2500 mm) creating dynamic daylight shadow lines across commercial facades and interiors.
Common Enquiry Formats: 405–625 × 2500 · 403–625 × 3000 mm
12 mm autoclaved dual-band shiplap grooved profile (175 mm / 275 mm groove pitch) in 405 × 2500 mm and 605 × 2500 mm delivering crisp factory-milled shadow joints and rapid installation (Smooth · Cedar Wood · Walnut Wood · Natural Stone · Decorative Stone · Slate Stone).
Common Enquiry Formats: 175 - 405 × 2500 · 275 - 605 × 2500 mm
12 mm autoclaved wide single-band shiplap profile (375 mm / 580 mm net face) in 410 × 2500 mm and 615 × 2500 mm delivering crisp factory-milled shadow joints and rapid installation (Smooth · Cedar Wood · Walnut Wood · Natural Stone · Decorative Stone · Slate Stone).
Common Enquiry Formats: 375 - 410 × 2500 · 580 - 615 × 2500 mm
12 mm autoclaved smooth-plane dual-channel profile (175 - 405 × 2500 mm · 1.013 m² · 150 pcs/pallet) delivering crisp factory-milled shadow joints and rapid installation (Smooth).
Common Enquiry Formats: 175 - 405 × 2500 mm
12 mm autoclaved wide smooth-plane dual-channel profile (275 - 605 × 2500 mm · 1.513 m² · 100 pcs/pallet) delivering crisp factory-milled shadow joints and rapid installation (Smooth).
Common Enquiry Formats: 275 - 605 × 2500 mm
12 mm autoclaved dense architectural batten-look multi-groove (100 - 415 × 2500 mm & 150 - 615 × 2500 mm) delivering crisp factory-milled shadow joints and rapid installation (Smooth · Cedar Wood · Walnut Wood).
Common Enquiry Formats: 100 - 415 × 2500 · 150 - 615 × 2500 mm
12 mm autoclaved 3-band linear groove geometry (125 mm band pitch) in 413 × 2500 mm and 413 × 3000 mm delivering crisp factory-milled shadow joints and rapid installation (Smooth · Cedar Wood · Walnut Wood · Natural Stone · Decorative Stone · Slate Stone).
Common Enquiry Formats: 125 - 413 × 2500 · 125 - 413 × 3000 mm
12 mm autoclaved 3-band wide linear groove geometry (190 mm band pitch) in 608 × 2500 mm and 608 × 3000 mm delivering crisp factory-milled shadow joints and rapid installation (Smooth · Cedar Wood · Walnut Wood · Natural Stone · Decorative Stone · Slate Stone).
Common Enquiry Formats: 190 - 608 × 2500 · 190 - 608 × 3000 mm
12 mm autoclaved 2-band architectural groove geometry (290 mm band pitch) in 608 × 2500 mm and 608 × 3000 mm delivering crisp factory-milled shadow joints and rapid installation (Smooth · Cedar Wood · Walnut Wood · Natural Stone · Decorative Stone · Slate Stone).
Common Enquiry Formats: 290 - 608 × 2500 · 290 - 608 × 3000 mm
12 mm autoclaved single-course perimeter-rebated plank (385 mm net face) in 403 × 2500 mm and 403 × 3000 mm delivering crisp factory-milled shadow joints and rapid installation (Smooth · Cedar Wood · Walnut Wood · Natural Stone · Decorative Stone · Slate Stone).
Common Enquiry Formats: 385 - 403 × 2500 · 385 - 403 × 3000 mm
12 mm autoclaved extra-wide single-course rebated panel (607 mm net face) in 625 × 2500 mm and 625 × 3000 mm delivering crisp factory-milled shadow joints and rapid installation (Smooth · Cedar Wood · Walnut Wood · Natural Stone · Decorative Stone · Slate Stone).
Common Enquiry Formats: 607 - 625 × 2500 · 607 - 625 × 3000 mm
Class A1 non-combustible 20 mm solid autoclaved fibre cement horizontal floor-band mouldings in 200 × 2500/3000 mm (KS-01) and 205 × 2500/3000 mm (KS-02), replacing fragile foam cornices.
20 mm thick Class A1 stepped horizontal floor-band & cornice profiles (KS-01: 200 mm, KS-02: 205 mm) in 2500 and 3000 mm lengths.
Common Enquiry Formats: 200 × 2500 · 200 × 3000 · 205 × 2500 · 205 × 3000 mm
Solid 20 mm autoclaved 200 mm wide stepped architectural floor-band moulding profile in 2500 mm (180 pcs/pallet) and 3000 mm (150 pcs/pallet) lengths with Class A1 fire safety.
Common Enquiry Formats: 200 × 2500 · 200 × 3000 mm
Solid 20 mm autoclaved 205 mm wide multi-stepped architectural cornice moulding profile in 2500 mm (180 pcs/pallet) and 3000 mm (150 pcs/pallet) lengths with Class A1 fire safety.
Common Enquiry Formats: 205 × 2500 · 205 × 3000 mm
20 mm thick Class A1 autoclaved window surrounds and corner trims across Flat Jamb (80–200 mm), 45° Beveled Jamb (80–200 mm), PS-01 (100 mm), PS-02 (120 mm), PS-03 (150 mm) and PS-04 (150 mm).
20 mm solid Class A1 window surrounds & corner trims in Flat, 45° Beveled (80–200 mm) and Stepped PS-01..04 (100–150 mm) profiles.
Common Enquiry Formats: 80 × 2500/3000 · 100 × 2500/3000 · 120 × 2500/3000 · 150 × 2500/3000 · 200 × 2500/3000 mm
20 mm solid Class A1 autoclaved minimalist square-edged flat window/door architrave and corner band in 80, 100, 150 and 200 mm widths in 2500 mm and 3000 mm lengths.
Common Enquiry Formats: 80 × 2500 · 100 × 2500 · 150 × 2500 · 200 × 2500 · 80 × 3000 · 100 × 3000 · 150 × 3000 · 200 × 3000 mm
20 mm solid Class A1 autoclaved 45°-chamfered window surround profile in 80, 100, 150 and 200 mm widths creating crisp angled reveal transitions in 2500 mm and 3000 mm lengths.
Common Enquiry Formats: 80 × 2500 · 100 × 2500 · 150 × 2500 · 200 × 2500 · 80 × 3000 · 100 × 3000 · 150 × 3000 · 200 × 3000 mm
20 mm solid Class A1 autoclaved compact 100 × 2500 / 3000 × 20 mm stepped window architrave profile (360 / 300 pcs/pallet) in 2500 mm and 3000 mm lengths.
Common Enquiry Formats: 100 × 2500 · 100 × 3000 mm
20 mm solid Class A1 autoclaved medium-width 120 × 2500 / 3000 × 20 mm decorative stepped window jamb profile (300 / 250 pcs/pallet) in 2500 mm and 3000 mm lengths.
Common Enquiry Formats: 120 × 2500 · 120 × 3000 mm
20 mm solid Class A1 autoclaved wide 150 × 2500 / 3000 × 20 mm classical stepped window architrave profile (240 / 200 pcs/pallet) in 2500 mm and 3000 mm lengths.
Common Enquiry Formats: 150 × 2500 · 150 × 3000 mm
20 mm solid Class A1 autoclaved 150 × 2500 / 3000 × 20 mm dual-stepped chamfered window surround profile (240 / 200 pcs/pallet) in 2500 mm and 3000 mm lengths.
Common Enquiry Formats: 150 × 2500 · 150 × 3000 mm
Overlapping horizontal lap-siding facade planks in 170 / 200 mm widths × 2500 / 3000 mm lengths (8 & 10 mm thickness) engineered for villas, light-steel residences and modular houses.
Weatherboard cladding planks (170 / 200 mm outer width, 8–10 mm) in wood-grain or smooth finishes for horizontal lap-joint facades and light-steel prefab homes.
Common Enquiry Formats: 170 × 2500 · 200 × 2500 · 170 × 3000 · 200 × 3000 mm
Compact structural sandwich press-panels engineered for prefabricated buildings, modular cabins and light-steel structures: two 8 mm Class A1 autoclaved fibre cement boards bonded to a 16 DNS EPS core (with project/MOQ evaluation for XPS, Stone Wool and Polyurethane) in Smooth and 5 Wood/Stone reliefs.
Flat smooth double-skinned composite wall panel (1250 × 2500 & 1250 × 3000 mm; 60, 80, 100 mm) with 8 + 8 mm autoclaved Class A1 fibre cement faces and 16 DNS EPS thermal core.
Common Enquiry Formats: 1250 × 2500 · 1250 × 3000 mm
Architectural 1250 × 2500 mm insulated ready-wall panel (60, 80, 100 mm) combining 5 embossed wood/stone 8 mm Class A1 fibre cement exteriors with a smooth interior face and 16 DNS EPS core.
Common Enquiry Formats: 1250 × 2500 mm
Three-layer ready-made wall panels combining 8 + 8 mm autoclaved Class A1 fibre cement skins with a 16 DNS EPS thermal core across 60, 80 and 100 mm thicknesses in smooth and 5 embossed reliefs.
Common Enquiry Formats: 1250 × 2500 · 1250 × 3000 mm
Prevent specification ambiguity before tendering: distinguish clearly between relief texture geometry (TX code), surface coating or core pigmentation method, and physical sample shade verification.
Bridge the gap between architectural wall take-offs (m²) and commercial sheet counts. Compare outer board geometry against installed lap coverage, add a realistic cutting allowance, and forward your summary directly to our WhatsApp quote desk.
Architectural fibre cement boards have crisp edges and high mineral density. Safe delivery from Turkish dispatch warehouses to European yards or construction sites depends on rigid full-length pallet support, moisture barrier discipline, and proper forklift handling upon arrival.
For flat and wood/concrete/colour architectural boards, 1250 × 2500 mm (3.125 m²) and 1250 × 3000 mm (3.75 m²) are the primary enquiry formats. Brick-relief panels frequently use pattern-matched outer sheets such as 1225 × 2590 mm or 1225 × 3000 mm, while horizontal lap cladding planks are commonly requested in 170 / 200 mm widths by 2500 / 3000 mm lengths. Exact availability is confirmed per order.
In dry interior linings and infill partitions, 6 mm, 8 mm, and 10 mm smooth boards are frequently evaluated. For exterior ventilated rainscreen facades, 8 mm, 10 mm, and 12 mm boards are common candidates, while deep-relief stone/brick/linear panels often require 10 mm or 12 mm to maintain sufficient residual core thickness. Final thickness must always be verified by the project structural/facade engineer.
Factory-coated panels feature an opaque or semi-transparent architectural paint system applied onto a natural mineral grey fibre cement core; saw-cut edges expose the grey core and require compatible edge sealing. Through-coloured panels incorporate mineral pigments throughout the entire board matrix so face and cut edges share the same colour family, typically finished with a matte hydrophobic or translucent protective coat.
Outer skins and core are stated transparently: both 8 + 8 mm autoclaved natural fibre cement skins are EN 13501-1 Class A1 non-combustible mineral boards, whereas the standard thermal core is 16 DNS EPS foam. Where a fully non-combustible core is required by fire code, Class A1 Stone Wool (Rockwool) core lamination is evaluated subject to project MOQ.
Lap cladding planks overlap horizontally to shed rainwater. For example, a 200 × 2500 mm plank has a geometric outer area of 0.50 m², but when installed with a 30 mm horizontal overlap its visible effective width is 170 mm (0.425 m² effective coverage per plank)—requiring roughly 17.6% more planks than raw outer m² before cutting waste.
Standard export supply focuses on full factory sheets and standard cladding planks for maximum transport safety and cost efficiency. Cut-to-size rectangular modules can be evaluated on a project basis when supported by a clear cutting list, repeatable module sizes, edge-treatment specification, and sufficient batch volume.
Physical density, bending strength class, moisture movement, and reaction-to-fire classification depend on the exact board formulation and factory coating build-up (e.g. uncoated mineral board vs multi-coat painted panel). Sharing variant-matched documents guarantees that your specification engineer reviews authentic test parameters.