SerFibro LightBoard — Homogeneous Dry-Facade & Interior Fibre Cement Board

SerFibro LightBoard was developed through targeted R&D to European standards (TS EN 12467 NT autoclaved technology) to answer the fastest-growing segment of modern high-rise, commercial and modular construction: lightweight interior wall linings and dry exterior infill/rainscreen facade systems. It bridges the gap between fragile gypsum sheathing boards and overly heavy conventional cement slabs.

Exterior gypsum sheathing boards and lightweight mesh-wrapped cement panels rely on bonded fibreglass mats or scrim skins for bending strength; if UV exposure, moisture or site abrasion damages that thin skin, the core chalks, blisters or delaminates. SerFibro LightBoard is 100% homogeneous right through its autoclaved mineral cross-section with zero surface mat, scrim or laminated layer—so cut edges stay crisp and delamination is physically impossible.

Mat-faced exterior sheathing systems force contractors to trowel cementitious basecoat mortar and embed alkali-resistant fibreglass mesh across the entire facade area before finishing—adding wet trades, weather delays and heavy labour costs. SerFibro LightBoard requires zero full-surface mesh or basecoat plaster during dry-facade or interior installation: panels can be mounted with open shadow joints or localized flexible joint treatment and painted directly.

In seismic zones, high-rise steel/concrete towers and rooftop extensions, every kilogram removed from perimeter infill walls reduces structural framing demand. SerFibro LightBoard substantially lowers wall dead load compared to conventional heavy cement boards, improves manual handling ergonomics for drywall crews, and cuts domestic road-freight and international container shipping costs per square metre.

SerFibro LightBoard covers three strategic floor-to-ceiling lengths: 1250 × 2500 mm (3.125 m² in 8, 10, 12 mm), 1250 × 3000 mm (3.750 m² in 8, 10, 12 mm), and a dedicated 1250 × 2800 mm (3.500 m²) structural dry-wall format produced in 14 mm (40 pcs/pallet) and 16 mm (35 pcs/pallet)—matching standard clear slab-to-slab heights with zero horizontal offcut waste.

Catalogued under TX-SM-01, the smooth homogeneous mineral face is supplied either Unprimed (for ceramic tiling in wet zones, industrial coating or raw architectural detailing) or Factory Pre-Primed with alkali-resistant primer so painting crews can apply breathable water-based pure acrylic or silicone exterior/interior topcoats directly on site.

Primary applications include slab-to-slab exterior dry infill walls replacing hollow brick/AAC masonry on multi-storey towers, ventilated rainscreen cladding, light-gauge steel residential/commercial envelopes, acoustic hotel and hospital partition walls, school/mall corridors requiring high impact resistance, and fire-rated shaft linings.

Mount SerFibro LightBoard onto galvanized steel C/U drywall studs or vertical rainscreen profiles (typically at 400–625 mm centres according to wind load and board thickness) over breathable vapour-permeable weather barriers on exterior walls. Fix with corrosion-resistant self-drilling wing-tip fibre cement screws and detail joints either as open ventilated shadow gaps (4–10 mm) or elastic polyurethane/hybrid sealant joints.

Autoclaved under high pressure and temperature, SerFibro LightBoard holds EN 13501-1 Class A1 non-combustibility with zero flame contribution or toxic smoke. It will not swell, soften, rot or support mould in damp cavities, and withstands hard-body and soft-body impacts far superior to paper-faced or glass-mat gypsum boards.

Because SerFibro LightBoard contains zero glass-fibre surface mat, installers avoid irritating fibreglass skin itch and fuzzy frayed edges during sawing. Cut sheets dry with carbide- or diamond-tipped circular saws connected to vacuum extraction, wipe alkaline dust dry immediately, and prime cut exterior arrises before painting.

Export pallets pack 75 / 60 / 50 pcs in 1250 × 2500 mm (8 / 10 / 12 mm = up to 234.38 m²), 40 / 35 pcs in 1250 × 2800 mm (14 / 16 mm = 140.00 / 122.50 m²), and 60 / 50 / 45 pcs in 1250 × 3000 mm (8 / 10 / 12 mm = up to 225.00 m²), delivering clean take-off planning for multi-storey tenders.

Store pallets on flat, dry indoor slabs away from standing water and rain so boards are installed dry. Lift sheets vertically off the pallet without dragging across the board beneath, and carry long 2500 / 2800 / 3000 mm boards vertically on edge with two operatives.

SerFibro exports LightBoard worldwide from Türkiye under EXW, FCA, FOB, CIF and DAP Incoterms. Drywall distributors and facade contractors can combine SerFibro LightBoard pallets in the same shipment with SerFibro Flex (for curved walls/columns), SerFibro Lam (for wet rooms) and exterior textured claddings.

Standard B2B quotations cover SerFibro LightBoard supply in the selected thickness (8–16 mm), format and finish (Unprimed or Pre-Primed) with export palletising. Upon request, CFY Engineering & Architecture also provides dry-facade wall build-up engineering, acoustic/fire partition detailing, sub-framing supply and site installation—reach us at +90 505 507 04 18 or [email protected].