SerFibro ColorBoard Smooth Through-Coloured Board

SerFibro ColorBoard Smooth (SF-CB-SMOOTH) represents our flagship flat through-coloured architectural facade panel. Mineral oxide pigments are blended directly into the cellulose-fibre, micronized-quartz and Portland-cement slurry prior to high-pressure autoclaving. Unlike surface-painted grey boards, the entire 10 mm cross-section carries the chosen colour—delivering timeless mineral depth, invisible scratch behaviour and crisp monochromatic open joints without site painting.

Engineered around the optimal 1250 × 2500 × 10 mm rainscreen sheet (3.125 m² geometric area), SF-CB-SMOOTH balances multi-storey wind-load spanning stiffness with ergonomic two-person site handling (~42.2 kg per sheet at 1350 kg/m³). Level 1 dimensional tolerances maintain length/width within ± 5 mm, smooth thickness within ± 10% e, squareness within ± 2 mm/m and edge straightness within ± 0.1% a.

Catalogued under TX-CB-SM and TX-SM-01, the smooth autoclaved face exhibits a calm, low-glare mineral aesthetic that highlights architectural massing and window proportions. As with all natural through-coloured mineral boards, installers must align rear production direction arrows identically across every elevation panel so subtle fibre orientation reflects daylight uniformly.

The SerFibro ColorBoard palette offers 7 mass-pigmented base colours—Natural (CB-NAT), Ash Grey (CB-ASH), Smoke Grey (CB-SMK), Anthracite (CB-ANT), Dark Beige (CB-DBJ), Amber Orange (CB-ORG) and Brick Terracotta (CB-BRK)—protected against water absorption and UV fade. In addition, 5 optional factory solution/marble-effect topcoat tones (Ash Grey TC-ASH, Smoke Grey TC-SMK, Anthracite TC-ANT, Orange TC-ORG, Brick TC-BRK) add subtle nuanced depth and enhanced stain resistance.

Because pigment runs right through the 10 mm sheet, workshop cutting, mitres, window-reveal returns and CNC perforations expose matching mineral colour rather than a contrasting grey core. After sawing, lightly sand cut arrises and apply clear breathable hydrophobic edge impregnation so rainwater sheds evenly without temporary dark damp rims.

SF-CB-SMOOTH is specified on corporate headquarters, universities, hospitals, cultural buildings, luxury residences, modular architectural pavilions and high-traffic interior atrium or lobby walls where A1 non-combustibility, natural mineral tactility and zero repainting downtime are decisive.

Mount panels on vertical aluminium or galvanized steel rainscreen rails backed by UV-resistant black EPDM strips, maintaining a continuous rear ventilation cavity and 8–10 mm open shadow joints. Use powder-coated aluminium/stainless facade rivets (with centralising sleeve for sliding points) or facade screws colour-matched to the selected CB-* / TC-* shade.

SF-CB-SMOOTH meets EN 12467+A2 Category A with MOR Class 2 ≥ 10.0 N/mm², passing freeze-thaw, wet-dry and warm-water durability with strength ratio RL ≥ 0.75 and completing 50 full heat-rain cycles without cracking or delamination. Tested at 600 °C without ignition or toxic fume release, it holds EN 13501-1 Class A1 rating alongside moisture movement max. 0.2%, Δt = 0.005 mm/mK, λ = 0.20 W/mK, μ ≤ 30 and 30% porosity.

Each 1250 × 2500 × 10 mm sheet provides 3.125 m² of gross geometric area (60 sheets = 187.5 m² per pallet). Because natural mineral raw materials give through-coloured boards their authentic character, schedule contiguous facade elevations within a single production order and include 8%–12% cutting/attic-stock allowance.

Pallets are standardized at 60 boards (187.5 m²) weighing approximately 2.55–2.65 tonnes gross per pallet including heavy-duty wooden export skids and surface protection. A standard 20 ft sea container or tilt road trailer typically carries 9 to 10 full pallets (~1687.5 m² to 1875.0 m²) depending on corridor axle weight limits.

Store pallets indoors out of direct sun and rain to avoid condensation staining under plastic wrap. Always lift panels vertically without sliding across the sheet below, handle finished faces with clean lint-free gloves, and brush/vacuum cementitious cutting dust off panel faces immediately so alkaline dust cannot set in morning dew.

SerFibro exports ColorBoard Smooth worldwide from Türkiye under EXW, FCA, FOB, CFR, CIF, CPT or DAP terms. Architects frequently combine ColorBoard Smooth pallets with matching-colour ColorBoard Striped (SF-CB-STRIPED), Stone (SF-CB-STONE) or Wood (SF-CB-WOOD) pallets in the same container for multi-texture facade compositions.

Request physical SerFibro ColorBoard hand samples showing both the 7 raw mass-pigmented shades and the 5 solution/marble-effect topcoat finishes alongside the EN 12467+A2 / EN 13501-1 Class A1 documentation pack for client and architect sign-off.

Standard material quotations cover SerFibro ColorBoard Smooth Through-Coloured Board (SF-CB-SMOOTH) in the confirmed dimensions and surface state along with export palletising. Upon request, our CFY Engineering & Architecture team also provides architectural project design, modulation consultancy, facade engineering, substructure coordination, and professional site application as dedicated items in your quotation.