SerFibro ColorBoard Striped Through-Coloured Board

SerFibro ColorBoard Striped (SF-CB-STRIPED) brings tactile linear rhythm to mass-pigmented fibre cement architecture. Fine parallel stripes pressed directly into the autoclaved 10 mm mineral sheet break up large facade volumes with subtle micro-shadows that shift from morning to dusk—without the heavy machining cost or reduced core strength of deep-routed planks.

Supplied in 1250 × 2500 mm sheets (3.125 m²) at 10 mm nominal thickness, SF-CB-STRIPED adheres to EN 12467+A2 Level 1 geometry for embossed sheets: length and width ± 5 mm, squareness ± 2 mm/m, edge straightness ± 0.1% a, and textured thickness tolerance of -10% e / +15% e to accommodate the pressed linear ridge-and-valley relief.

Classified under TX-CB-LN, the linear stripes run parallel to the 2500 mm board length. Panels can be installed vertically to accentuate building height on multi-storey facades and lobby columns, or horizontally on spandrel bands and podium walls—provided orientation and rear arrow direction remain consistent within each architectural zone.

SF-CB-STRIPED shares the exact 7 mass-pigmented base colours (Natural, Ash Grey, Smoke Grey, Anthracite, Dark Beige, Amber Orange, Brick Terracotta) and 5 optional solution/marble-effect topcoat tones as ColorBoard Smooth—enabling architects to alternate smooth and striped panels in identical tonal harmony across the same elevation.

Cut panels face-down or using a guide-rail diamond circular saw blade with dust extraction for crisp arrises across the striped relief. Because the 10 mm mineral core is pigmented throughout, exposed cut edges at open vertical/horizontal joints blend seamlessly once sealed with clear hydrophobic edge protection.

Popular on office facades, retail podiums, hotel entrances, recessed window spandrels, auditorium foyers and executive reception walls, SF-CB-STRIPED adds tactile depth where flat panels feel too plain yet heavy profile cladding would overpower the design.

Install on vertical aluminium or galvanized steel rails with continuous rear air circulation (min. 20–40 mm), black EPDM cushion strips and 8–10 mm open joints. Use colour-matched dome-head facade rivets with centralising drill sleeves so fixings seat cleanly against the fine linear relief without over-tightening.

Autoclaved at high pressure, SF-CB-STRIPED achieves MOR Class 2 ≥ 10.0 N/mm², density 1350 ± 50 kg/m³, freeze-thaw/wet-dry/warm-water ratio RL ≥ 0.75, 50 heat-rain cycles without defect, moisture movement max. 0.2% and EN 13501-1 Class A1 non-combustibility (tested at 600 °C without ignition or toxic gas).

Gross geometric area is 3.125 m² per 1250 × 2500 mm panel. Because striped offcuts cannot be rotated 90 degrees without turning the stripe direction perpendicular to adjacent panels, budget an 8%–12% cutting allowance when laying out window surrounds and fascia strips.

Packed 60 panels (187.5 m²) per rigid horizontal wooden export pallet with protective interleaving between embossed surfaces, heavy corner guards and moisture-barrier shrink hood, tailored for safe international road and container sea freight.

Never drag panels horizontally off the pallet, as grit can mar the linear ridges. Lift vertically with two people, store pallets flat in dry indoor conditions away from solar heat buildup, and brush dry saw dust out of the stripe valleys immediately after cutting.

Dispatched from Türkiye under EXW, FCA, FOB, CFR, CIF, CPT or DAP Incoterms. Consolidate ColorBoard Striped with ColorBoard Smooth, Stone or Wood pallets on a single trailer or 20 ft container to streamline customs clearance and freight cost.

Order physical ColorBoard Striped hand samples to inspect the actual stripe pitch, shadow depth and mass-pigmented colour under natural site daylight alongside our EN 12467+A2 TDS and DoP.

Standard material quotations cover SerFibro ColorBoard Striped Through-Coloured Board (SF-CB-STRIPED) in the confirmed dimensions and surface state along with export palletising. Upon request, our CFY Engineering & Architecture team also provides architectural project design, modulation consultancy, facade engineering, substructure coordination, and professional site application as dedicated items in your quotation.