Wood-Textured Fibre Cement Board

SerFibro Wood combines the rapid coverage of full-format fibre cement sheets with tactile timber-grain embossing. Architects, modular home builders and facade contractors specify it to introduce organic surface shadow into contemporary mineral, glass and steel elevations without relying on solid timber cladding boards.

Standard enquiries focus on 1250 × 2500 mm (3.125 m²) and 1250 × 3000 mm (3.750 m²) full sheets in 8, 10 and 12 mm thicknesses. Because wood-grain relief is formed by dedicated pressing plates or rollers, format availability is tied directly to the selected grain code (TX-WD-01 or TX-WD-02) and confirmed per order.

Two primary timber textures are catalogued: TX-WD-01 features broader, cathedral-style walnut grain crowns, whereas TX-WD-02 presents a tighter, straighter cedar-type grain. On full sheets, the grain runs parallel to the long edge (2500 or 3000 mm). Rotating strips 90 degrees during cutting will change light reflection noticeably, so panel grain direction must be coordinated on elevation drawings.

Buyers must note an essential distinction: uncoated (raw) Wood boards display the embossed wood grain in natural cement grey—often chosen intentionally for architectural concrete-timber aesthetics or site staining. If you expect a brown walnut, oak or cedar colour out of the crate, specify a factory-coated variant or clarify compatible site-applied dual-tone glaze systems.

SerFibro Wood is supplied as square-edged full boards that contractors frequently rip into architectural facade bands or spandrel panels. If your project requires narrow overlapping clapboard strips instead of full sheets, compare this product with SerFibro Siding (SF-SIDING) or submit your custom strip schedule for cutting evaluation.

Typical applications include ventilated exterior wall zones on residential developments, light-steel prefabricated villas, modular educational or hospitality units, gable ends, soffits and commercial facade feature zones where documented product suitability aligns with local building regulations.

Full-size wood-textured boards are mounted with open ventilation joints on plumb metal or timber support rails. Fastener heads should sit flush on stable zones without crushing the embossed grain ridges; minimum edge distances and intermediate rail centres must follow the matched variant datasheet.

Because embossing creates peaks and valleys across the face, structural calculations must account for the effective minimum section thickness stated in the manufacturer TDS rather than peak thickness alone. Request the variant-matched TDS and available test reports during specification.

Each 1250 × 2500 mm sheet equals 3.125 m² geometric area, and 1250 × 3000 mm equals 3.750 m². Because grain direction cannot be rotated freely to nest offcuts into perpendicular facade zones, directional textures typically require a slightly higher cutting waste allowance (often 8% to 15%) than non-directional boards.

Wood-textured boards are stacked flat on reinforced wooden export pallets with edge guards and stretch/hood wrapping; factory-coated variants include protective face interleaving so embossed peaks do not abrade during road or sea transit. Exact board count and gross weight per pallet are confirmed in your quotation.

Keep pallets under dry roofed shelter on level bearers. Never slide an embossed board horizontally across the sheet below, as mineral grit can scratch the grain relief or factory paint layer. Carry boards on edge with two handlers and remove cutting dust promptly from textured grooves before moisture condenses.

Shipments are arranged from Türkiye by curtain-side road trailer or sea container depending on destination country and payload efficiency. Preferred Incoterms (EXW, FCA, FOB, CFR, CIF, CPT or DAP) and named destination port or city are reviewed and stated transparently in your written commercial offer.

Screen photographs cannot fully convey three-dimensional grain depth or dual-tone wood coatings. Request hand samples of TX-WD-01 and TX-WD-02 alongside the variant-matched Technical Data Sheet so your architectural team can inspect relief scale under natural exterior light.

Standard material quotations cover SerFibro Wood — Wood-Textured Fibre Cement Board (SF-WOOD) in the confirmed dimensions and surface state along with export palletising. Upon request, our CFY Engineering & Architecture team also provides architectural project design, modulation consultancy, facade engineering, substructure coordination, and professional site application as dedicated items in your quotation.